Make An Inexpensive Light Tent for Shooting Miniature Football Players

How to Make An Inexpensive Light Tent for Shooting Miniature Football Players

Light Box (tent) in use

Light Box (tent) in use

by Darren Rowse

Materials Needed:

1.) A Box – It could be any size you want as long as you can light it! I prefer it to be as square as can be. You can find boxes anywhere for free. I got mine from work in which they throw out anyway. You can also find boxes in the back of strip malls, grocery stores, appliance stores or basically any place that makes or sells products. Thicker the better! (Free)

2.) Fabric ‘ This again could be any type. In my box I used white muslin fabric that is found at your local arts and craft store. Buy enough to cover the entire box. (4.00$ US or 1.99$ a yard) People suggested other fabrics like White Nylon and white fleece. If your extremely cheap and have some white under shirts laying around. Cut up the sides to where you have two halves of the shirt. If you use multiple shirts, be sure that the color matches or your end result may not turn out as you like it

3.) Tape ‘ I use tape to secure the fabric to the sides of the box. Reason being is that In-case you want to try out different fabrics. I use regular masking tape. (1.00$ US A Roll)

4.) Glue ‘ You can use a “Glue Stick” (1.00$ US a Stick) or spray adhesive (5.00$ US per Can) to stick the lining in the box.

5.) Matte Poster Board ‘ This will line the inside of the box and will also serve as your back round (.50 a sheet X2). I would suggest to buy 2 or 3 sheets as you will be cutting up two to line your box (Could be more depending on the size of your box) and one for the back round. If you wanted a different back round you can also pick up different colors.

6.) Lights ‘ You will need to light this box and this could be the most expensive part of the box unless you already have the lights. In my opinion lighting is the most important part of this box. Without it you will not get the picture you desire. I went to my local hardware store and picked up some “Daylight” Bulbs. Using regular light bulbs will cast a yellow light and should be avoided. I purchased “n:vision” 90 watt equivalent compact florescent bulbs ($7.00 US). Basically any “Full Spectrum” light bulbs will do.

Also suggest a lighting fixture. If you have a one of those desk work lamps, It will work fine. If you don’t I suggest getting a “Clamp On Work Light”. At my local home depot they only had two kinds, A smaller reflector dish (5″) for 5.99$ (US) or the 10.5″ reflector for 11.99$ (US).

7.) Miscellaneous Tools ‘ Tape ruler, Ruler or any straight edge, scissors and knife

Now that you have the Materials I will show you out to make a light tent step by step. When you’re done you can take nice clean and crisp product shots.

Step By Step Process:

A) Take your box with a tape ruler and marker and measure in 2″ from the side of the box marking multiple points with your marker. When your done you will see your border, connect the points using your straight edge to where you should have a nice looking square/rectangle in the middle of the box with a 2″ border around it. Leave the top and bottom of the box alone as you will not need to mark it

B) Cut out the boxes you’ve drawn. Repeat that to the sides of the box where you have drawn the boxes. When you’re done, cut off the top of the box or remove the flaps on the top of the box. LEAVE THE BOTTOM INTACT!

C) Now take your poster board and make lines with your marker for every two inches 16 times. Then proceed to cut out 16 strips with your scissors.

D) Glue the paper strips into the box. Make sure the side with marker goes against the cardboard so it can not be seen.

E) Take another piece of poster board and cut is so the width is the same as the inside of the box and the length is much longer then the box.

F) Place the long piece of poster board into the box to where the piece curves to the bottom. Avoid creasing as it will show up in your photo. Cut off excess paper that is sticking out the top.

G) Cut your fabric to where it will cover the holes. Then cut a big piece to where it will cover the top of the box.

H) Tape the fabric to cover the holes in the box except the one that is facing your background. Then tape the top piece on.


Now all you got to do is light the top of the box and start snapping away!

There are many variations you can do to get the photo you want. If you’re having a shadow problem I suggest lighting the other sides of the box. If you’re getting vignetting, (In photography and opticsvignetting (pronounced /vɪnˈjɛtˌɪŋ/) is a reduction of an image’s brightness or saturation at the periphery compared to the image center.)  I suggest a lens hood or moving the lens more into the box. Photoshop could be a handy tool also! Since my lens and camera are not the cleanest I tend to photoshop out the dust that is sitting on or in my camera. I also adjust the levels so it’s brighter.

Camera sticking into the box

The Light box in action

Darren Rowse is the editor and founder of Digital Photography School. He lives in Melbourne Australia and is also the editor of the ProBlogger Blog Tips and TwiTip Twitter Tips blogs.

Here is a link to another variation of the light box.


Comments (3)

Trackback URL | Comments RSS Feed

  1. ChrisStacey says:

    Very informative “blog”.Simple and inexspensive.Great info. Thanks.

    Chris Stacey

  2. Dimitri says:

    Great article ! A little addition concerning lights : you can use “cold” or “daylight light bulbs (those “eco daylight” 15-20w works fine), and you also can add lights on sides of the box, I believe (I remember have seen a similar system somewhere).

    Last thing, concerning photo software : you can use photosho elements, often given with your PC or graphic card, or you can use GIMP wich is a free and open source pro software too, and available on linux, mac and pc.

    thank you for that article, regards


  3. detroitchild says:

    Wow….this information is invaluable! Looking forward to more like it.

    Thanks Darren

Leave a Reply

You must be logged in to post a comment.